More than likely there may already be a solution for your particular laptop, desktop, or motherboard. Other times I would select my boot drive to install MacOS, then get a memory error right away. Yet later on it didn't work again, but the OsxAptioFix3Drv driver did work! What would happen is I would boot to the flash drive, see the options for loading, select my boot drive, see a bunch of text appear on the screen and scroll quickly (known as verbose mode, totally normal), but it would reboot instead of stopping showing me where the error was. Somehow when I tried the OsxAptioFixDrv driver instead, that got me through to the MacOS screen where I could then install MacOS to my test hard drive. My i5 section had a OsxAptoFix3Drv driver, but when I installed it to the booting flash drive using one method, I was getting memory issues when attempting to select my flash drive after booting. When rewriting the book I was using my i5 Hackintosh on the Windows side to start from scratch, but using the kext and driver folders from the Hackintosh side as a starting point. ROADBLOCK! The section for Memory fixes is tricky. I'll also cover preventative measures for protecting files so you'll have a working backup if things go wrong. There's no reason to fear editing any files if you haven't done so before. While the initial install does add extra lines of code in files, I'll go over ways to clean up the code. The vanilla install also results in a few slimmer files compared to somewhat bloated files from the website. While the vanilla process is more involved than the techniques used in previous version of my eBook, it's also more open to learning how things work and gives the builder more control over their hardware and software. The majority of this info was taken from the Hackintosh Vanilla Desktop Guide and was crucial in getting my previous systems working much better than before. Launchctl load /System/Library/LaunchDaemons/ steps to create a bootable installer using Clover on a Windows computer are different than that on a Mac computer, but if you've come to this page you already have a Mac and want to stick to the familiar OS you know, or use Windows and may just want to get a preview on how MacOS looks and feels. Launchctl load /System/Library/LaunchDaemons/ The following commands *may* load the necessary items to run diskutil: Single User Mode also only starts a minimal system, leaving many frameworks and daemons unloaded, including some required by diskutil. To mount the system drive as read/write, use this command: Single User Mode mounts the system volume as read-only. In my professional opinion, nobody should ever run the commands listed below. I take no responsibility if in using this information, you damage your hardware or lose data. Someone in your situation should take this computer to an Apple Authorized Service Center and have the display replaced with Apple parts. I sympathize with your situation, but this is getting way beyond anything supported or recommended. ![]() Run the command: sudo mount -t msdos /dev/disk0s1 /Volumes/efi ![]() Mount the EFI partition at the efi mount point. ![]() We can create a directory called efi within /Volumes by running the following command: mkdir /Volumes/efiģ. On Mac OS X, mount points are typically created in /Volumes. In this case, the volume identifier of the EFI partition is disk0s1Ī mount point is a directory where a non-booted volume is mounted. The output should look something like this: /dev/disk0Ģ: Apple_HFS Macintosh HD 250.1 GB disk0s2ģ: Apple_Boot Recovery HD 650.0 MB disk0s3 Discover the volume identifier for your EFI boot partition. To mount an EFI boot partition, follow these steps:ġ. Before you read any further, take note: altering your EFI boot partition is not supported by Apple and The Mac Admin takes no responsibility if you render your computer(s) unbootable by mounting and modifying this partition. However, the EFI partition is used as a staging area for firmware updates.” When people look to create non-standard boot environments or attempt to build a hackintosh, the first step is often mounting and modifying the EFI boot partition. Here’s the answer to another reader request…Īccording to WIkipedia, “On Apple–Intel architecture Macintosh computers, the EFI partition is initially blank and not used for booting.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |